2006 Mack CTP recalls and problems
The 2006 Mack CTP has 4 safety recalls. Recall repairs are free at any Mack dealer.
Recalls may cover only some 2006 Mack CTP vehicles. Check your VIN at NHTSA ↗ to see open recalls for your exact car.
2006 Mack CTP recalls
Recall 07V-497: Trailer Hitches
Problem: On certain trucks equipped with a saf holland simplex fifth wheel, the lever arm pivot bolt may have been over tightened. An over tightened pivot bolt can distort the pivot bolt spacer sleeve, which may prevent the fifth wheel latch jaw from closing and latching securely around the trailer king pin.
Risk: There is a possibility that the pivot bolt can become loose without the driver's knowledge. When this occurs, the driver could drive away and the trailer could become disengaged, increasing the risk of a crash.
Fix: Dealers will replace the pivot bolt and sleeve with a hex head shoulder bolt and washer free of charge. The recall began on january 28, 2008. Owners may contact mack trucks at 1-800-528-6586.
Recall 07V-361: Service Brakes, Air
Problem: On certain trucks equipped with parker single check valves (Scv) provided by bendix. The defect exists in the parker scv that connects with the supply port of the sr-7 spring brake modulating valve. After prolonged use of the parker scv, the valve body retainer may become excessively worn and eventually break apart. Pieces of the parker scv can become lodged inside the sr-7 spring brake modulating valve, potentially causing either leakage out of the sr-7 valve or preventing air from properly exhausting from the sr-7 valve.
Risk: This condition can cause a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button. These conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in the case of loss of primary circuit, inability to modulate the spring brakes.
Fix: Mack is working with bendix to replace the parker single check valve. The recall began on january 9, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
Recall 07V-360: Parking Brake
Problem: On certain trucks equipped with bendix sr-7 spring brake modulating valves, the internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
Risk: This could delay or failure in applying the parking brakes which could result in a vehicle roll away, increasing the risk of a crash.
Fix: Mack is working with bendix to repair these vehicles (Please see 07e037). Bendix will install a check valve repair kit for the affected sr-7 spring brake modulating valve free of charge. The recall began on january 10, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
Recall 07V-098: Service Brakes, Hydraulic
Problem: On certain trucks, the cotter pin that retains the brake pedal clevis pin may not have been installed. The clevis pin connects the brake pedal to the brake foot valve.
Risk: If the pin were to come loose, the driver would not be able to apply the service brake, which could result in a crash.
Fix: Dealers will inspect to see if the cotter pin is missing. If the pin is missing, the cotter pin will be installed. Owners are being advised not the drive the vehicle until the pin has been installed. The recall began on march 26, 2007. Owner may contact mack truck at 1-800-528-6586.
Other Mack CTP years
Frequently asked questions
Does the 2006 Mack CTP have any recalls?
Yes — NHTSA lists 4 recalls for the 2006 Mack CTP: 07V-497 (trailer hitches), 07V-361 (service brakes, air), 07V-360 (parking brake), 07V-098 (service brakes, hydraulic). Not every vehicle is affected, so check your VIN at nhtsa.gov/recalls.
Are Mack recall repairs free?
Yes. Safety recall repairs are free at authorized Mack dealers, whether you are the first owner or bought the car used.